Can I use acrylic instead of cotton?

Acrylic works well here and holds the leaf shape nicely, though cotton or a cotton blend will give you crisper stitch definition on the chevron rows. Either fiber choice is fine for this project.

Is the floral wire required?

It is optional, but I recommend it if you want the leaves to hold a natural, slightly curved stance rather than lying flat. Skip it if you prefer a softer, more relaxed look.

What size pot should I use?

The pattern calls for a terracotta pot between 4 and 5 inches in diameter. Anything outside that range will change how far the soil disc and pot rim need to stretch.

How do I know when to stop the pot rim rows?

Keep working Row 2 of Part 4 until the strip wraps comfortably around your actual pot rim before joining the ends. It is fit by trying it against your pot rather than a fixed row count.

Ocean blue snake plant amigurumi crochet pattern

LevelIntermediate
Time4-6 hours
Hook3.5 mm
YarnWorsted

About This Pattern

This one has that calm, sun-on-the-windowsill mood, the kind of project that makes you want to clear a spot on the shelf before you even finish the last leaf. The dark teal, medium turquoise, and light seafoam shift like light moving across a real snake plant. It feels more like a little sculpture than a toy.

Set it in the terracotta pot on a windowsill, a bookshelf, or a desk, and it just sits there looking confident. No watering, no yellowing leaves, no guilt when you forget it for a week. It reads as a real plant from across the room, which is honestly the whole point.

I like it best next to other small, textured things, a stack of books, a ceramic mug, a trailing pothos that actually needs tending. It holds its own without demanding attention.

Start with the chevron leaf foundation, working the paired decrease and center increase row until the leaf reads as pointed and structured.
Build out the additional leaves in the color sequence so the finished plant shows the full range from dark teal to light seafoam.
Work the rounded piece in increasing rounds from a magic ring to form the base that everything else will stand on.
Insert floral wire or pipe cleaners into the leaves if you want them to hold a gentle curve rather than flop.
Stuff the rounded base with fiberfill so it holds its shape once it sits inside the terracotta pot.
Crochet the back-loop-only strip long enough to wrap the pot rim, then slip stitch the short ends into a ring.
Fit the soil disc down into the pot so it sits just below the rim before adding the leaves.
Arrange and secure the finished leaves into the soil disc to complete the whole plant.

On the desk

Yarn

Color A (Dark Teal): Approximately 80 yards of worsted weight yarn
Color B (Medium Turquoise): Approximately 80 yards of worsted weight yarn
Color C (Light Seafoam): Approximately 60 yards of worsted weight yarn
Color D (Sage Green): Approximately 40 yards for the pot rim
Color E (Brown): Approximately 20 yards for the soil

Tools

3.5mm (E/4) crochet hook
4.0mm (G/6) crochet hook for the pot rim
Tapestry needle
Stitch markers
Polyester fiberfill stuffing
Floral wire or pipe cleaners (optional, for leaf stability)
One terracotta pot, 4 to 5 inches in diameter
Scissors

Stitch shorthand

ch — chain
st — stitch
sts — stitches
sl st — slip stitch
sc — single crochet
inc — increase
sc2tog — single crochet 2 stitches together (decrease)
blo — back loops only
fo — finish off

Ocean blue snake plant amigurumi crochet pattern

Easy to get wrong

Losing the chevron shape

Keep a stitch marker at the center stitch of the Large Leaf Foundation so you never miscount before the 3-sc increase. If the zigzag looks flat, check that both edge decreases were worked, not just one.

Rib band comes out too tight

If the Part 4 strip refuses to wrap the pot rim comfortably, add a few more BLO rows rather than stretching it. The back-loop-only ribbing has some give, but it should sit without strain.

Leaves flop instead of standing

Skipping the floral wire or pipe cleaners leaves soft leaves that sag over the pot edge. Insert the wire before you close up each leaf, not after.

Between the songs

The satisfaction here is in the chevron technique on the Large Leaf Foundation, where a sc2tog at each edge and a 3-sc increase at dead center turn a flat strip into a pointed, structured leaf shape. That single row repeated builds real dimension without any shaping charts to follow. Then the pot rim flips the texture entirely, working back loop only so you get that ribbed, knit-like band wrapping the terracotta. Three yarn weights of color fade from dark teal through turquoise to seafoam, so each leaf you finish adds visible depth to the whole piece. It is a project that teaches two distinct skills, sharp shaping and textured rounds, inside one small, giftable object.

Listener questions

Can I use acrylic instead of cotton?
Acrylic works well here and holds the leaf shape nicely, though cotton or a cotton blend will give you crisper stitch definition on the chevron rows. Either fiber choice is fine for this project.
Is the floral wire required?
It is optional, but I recommend it if you want the leaves to hold a natural, slightly curved stance rather than lying flat. Skip it if you prefer a softer, more relaxed look.
What size pot should I use?
The pattern calls for a terracotta pot between 4 and 5 inches in diameter. Anything outside that range will change how far the soil disc and pot rim need to stretch.
How do I know when to stop the pot rim rows?
Keep working Row 2 of Part 4 until the strip wraps comfortably around your actual pot rim before joining the ends. It is fit by trying it against your pot rather than a fixed row count.

Original pattern: https://crochetwithmia.com/ocean-blue-snake-plant-amigurumi-free-crochet-pattern/

About the Author

Marisol QuinteroWho runs Crochet Obsessed, why a stitch count sits at the end of every round, how a pattern gets written here, and the things this site will never do.

Ocean blue snake plant amigurumi crochet pattern

About This Pattern

On the desk